I decided on cleaning my laptop fans today, which I’ve been procrastinating for about a year now because of this one screw. But I just can’t seem to open this with my screwdriver, since whatever I did back when I last opened it it’s nearly circular now. Is there a way to unscrew this?
Old life hack that occasionally works for this is to use a rubber band. Grab a rubber band wide enough to cover the screw head, push the screwdriver into the screw through the rubber band, and pray it has enough grip to twist the screw loose. Good luck with whatever method you use.
Old Nintendo security screws were easily overcome by melting the end of a pen tube (the clear plastic Bic’s were always my preference), and jamming it in there holding it still while it cooled. Could work in this case.
I have successfully done this with a fuse box.
Never in the history has that worked for me of doing laptop repair professionally.
Thank you. This is always in the list of handyman hacks, and using a rubberband has never worked for me either. I’m convinced 90% of the people recommending it are just repeating what they’ve heard and haven’t actually tried it.
I’ve tried it a dozen or so times, maybe worked 2-3 of them. I keep it in my arsenal of tricks because it’s quick and easy to try with no negative repercussions if it doesn’t work.
It’s worked for me but with a couple layers of insulation tape rather than a rubber band.
A dab of super glue in the screw hole, find a screw driver you don’t really care about, add a drop of superglue accelerator
If its big enough, try the rubber band trick to get some grip.
If its a tiny electronic screw, you’ll have to very carefully coax it out with either some needle nose pliers by gripping the outside, or by using a slightly larger screwdriver head and ensuring it doesn’t spin (very tricky, easy to strip screw further, using rubber band here might also help).
If the case can handle it, you can use the larger head and give it some decent amount of pressure to make sure it doesn’t spin when you turn. Again be careful, because pushing too hard could break the case.
You might have to inch it fractions of a turn at a time to make sure it doesn’t break, so it’ll take a while before it becomes loose enough to spin out by hand.
Carefully dremel a slot in the screw head and use a flat head screwdriver.
Make sure you don’t get any dust into the electronics.
Take the drill bit out of your drill. Open the chuck up all the way and place it over the screw. If there is enough screw head there you might be able to grab it with the drill and just unscrew.
Edit: looking at the other picture makes me think it is recessed and that wouldn’t work then.
Cripes, it never even occurred to me that you could do this with a chuck. Thanks for expanding my mind.
Try addinv a rubber band between the screw and the screwdriver, it adds friction which sometimes (usually not) helps
Drill in it, put fitting torx in hole, unscrew.
That usually works, however you need too much force to press the torx bit into the hole to do that on sensitive electronics. That screw is probably only threaded into plastic.
Looks like it sticks out a bit. Cut a slot in it and use a flathead.
So if you have a dremel and steady hands, a cut off wheel can make your own slot for a straight Phillips.
Just be careful to not knick anything else. This is more of a last resort thing, but I’ve never had it not work.
Learn from my mistakes, mask off your laptop’s ports and vents before you do this
Ooof. Not something I’d have thought of myself…
Benefit of your hindsight it’s obvious… lol. How bad were the sparks?
Flathead/standard not a straight Philips.
Flathead is a description of the head profile, like panhead. Slotted is the screwdriver type that is just a single slot.
It could be a regional thing. Where I’m from a screw with a single straight slot can be called a flathead whether the actual head of the screw is flat or domed.
It gets called that everywhere. Most people never need to know the actual specs for a screw, so language diverges from the classification system.
I usually keep the corrections to myself, but when somebody else is already correcting someone and they say the wrong thing too it becomes hard.
The same thing happened to me… Luckily it was one of screws on the outer edges of the thermal housing. HP’s screws are such dogshit that they get easily stripped. I tried everything from rubber band to superglue. Eventually I had to drilled the screw head away.
It’s easier not to clean them. I throw down tin foil before I make paninis in my hp laptop, because THAT’S ALL THEY’RE FUCKING GOOD FOR.
I think the answer is no.
