I don’t understand why you’d install Debian before the hypervisor.

Edit: TiL thx for the replies. I legit didn’t know of these scenarios.

Never understood how its continued. I mean, we all do- lobbying. But when 3/4th of the commercial/ad is just different versions of super death side effects…just why

Ya, hindsight it’s a dumb comparison.

For sure. Plenty of times I’ve had to go power cycle a little desk printer just for it to work again. Oddly, commercial label printers (like TSC) have been surprisingly ok, even in large industrial shops.

Maybe it’s the environments I work in, but WiFi printing always ends in tragedy.

Wireguard has effectively zero impact on my setup.

Can confirm, I’ve been using it for about three years now. With some minimal tweaks for my own us case.

It auto updates itself, can use LetsEncrypt. I’ve had an A to A+ rating from their own security thing. It does usually stay a few minor point releases behind, but that’s never been an issue for me.

I set mine up with a no-ip dyndns for free. Lots of options here op. But in the long run having any domain is going to smooth out the process. Also don’t skip over LetsEncrypt cert.

Overall good. The only slowness is right after login. After it loads everything it’s pretty responsive. Using the snap version (I know, snap bad. But in this case it was the only way I got it going.).

Self updates,.get email notifications when it updateab

Take a look at “Seeker”. Its a client for the SoulSeeker network. Nicotine+ for desktop is nice too.

Ya don’t need ATT’s modem. Some copy pasta I’ve put together:

If it’s fiber, you don’t need the modem. You’ll still need it once every few months.

Things you’ll need:

1. your own router
2. cheap 4 port switch (1gig pref)

Setup: Connect gpon (the little fiber converter box they installed on the wall near modem) wan to any port on 4port switch. Then from switch to gpon port of modem (usually red or green port). Make sure modem fully syncs. Once this happens, you can move the cable from the modem to your own routers wan port. Done! Allow router a few moments to sync as well.

Now, every once in a while they’ll send a line refresh signal that will break this, or if a power outage occurs. In such case, you’ll just plug back in their modem, move cable back to gpon port of modem, wait for sync. Move cable back to router.

Bonus: Hook up all this to a battery backup and you’ll have Internet even during power outages, at least for a while.

Not sure if the rpi3 can use the 64bit version, or if it’s possible for it use an SSD like the the 4 can?

I’m using an old HP z420 box. It supports up to 128gigs of ecc ram (which I have), has tons of drive and SATA options.

It could be possible to repurpose the chassis for custom builds too.

Honestly, maybe having it also backup to a consumer grade external HDD enclosure. As much as it pains to say. But like one of those WD mybook things or similar. Designed to be dead simple for the average person.

If it’s fiber, you don’t need the modem. You’ll still need it once every few months.

Things you’ll need:

1. your own router
2. cheap 4 port switch (1gig pref)

Setup: Connect gpon (the little fiber converter box they installed on the wall near modem) wan to any port on 4port switch. Then from switch to gpon port of modem (usually red or green port). Make sure modem fully syncs. Once this happens, you can move the cable from the modem to your own routers wan port. Done! Allow router a few moments to sync as well.

Now, every once in a while they’ll send a line refresh signal that will break this, or if a power outage occurs. In such case, you’ll just plug back in their modem, move cable back to gpon port of modem, wait for sync. Move cable back to router.

Edit: (after thought) put all this equipment on a battery backup and you’ll still have Internet during short power outages.

Not viable strategy, firing the wife incurs a 50% net worth severance package.